| General specifications |
| Signal type | Analog input |
| Functional safety related parameters |
| Safety Integrity Level (SIL) | SIL 2 |
| Supply |
| Connection | terminals 14+, 15- or power feed module/Power Rail |
| Rated voltage | 20 ... 30 V DC |
| Ripple | within the supply tolerance |
| Power dissipation | ≤ 0.98 W |
| Power consumption | max. 0.98 W |
| Interface |
| Programming interface | programming socket |
| Input |
| Connection side | field side |
| Connection | terminals 1, 2, 3, 4 |
| RTD | type Pt10, Pt50, Pt100, Pt500, Pt1000 (EN 60751: 1995) |
| type Pt10GOST, Pt50GOST, Pt100GOST, Pt500GOST, Pt1000GOST (6651-94) |
| type Cu10, Cu50, Cu100 (P50353-92) |
| type Ni100 (DIN 43760) |
| | Measuring current | approx. 200 µA with RTD |
| | Types of measuring | 2-, 3-, 4-wire connection |
| | Lead resistance | max. 50 Ω per line |
| | Measurement loop monitoring | sensor breakage, sensor short-circuit |
| Thermocouples | type B, E, J, K, N, R, S, T (IEC 584-1: 1995) |
| type L (DIN 43710: 1985) |
| type TXK, TXKH, TXA (P8.585-2001) |
| | Cold junction compensation | external and internal |
| | Measurement loop monitoring | sensor breakage |
| Potentiometer | 0 ... 20 kΩ (2-wire connection), 0.8 ... 20 kΩ (3-wire connection) |
| Voltage | selectable within the range -100 ... 100 mV |
| Input resistance | ≥ 1 MΩ (-100 ... 100 mV) |
| Output |
| Connection side | control side |
| Connection | output I: terminal 7: source (-), sink (+), terminal 8: source (+), terminal 9: sink(-) |
| Output | Analog current output |
| | Current range | 0 ... 20 mA or 4 ... 20 mA |
| | Fault signal | downscale 0 or 2 mA, upscale 21.5 mA (acc. NAMUR NE43) |
| | Source | load 0 ... 550 Ω |
| open-circuit voltage ≤ 18 V |
| | Sink | Voltage across terminals 5 ... 30 V. If the current is supplied from a source > 16.5 V, |
| series resistance of ≥ (V - 16.5)/0.0215 Ω is needed, where V is the source voltage. |
| The maximum value of the resistance is (V - 5)/0.0215 Ω. |
| Transfer characteristics |
| Deviation | |
| | After calibration | Pt100: ± (0.06 % of measurement value in K + 0.1 % of span + 0.1 K (4-wire connection)) |
| thermocouple: ± (0.05 % of measurement value in °C + 0.1 % of span + 1 K (1.2 K for types R and S)) , includes ± 0.8 K fault of the cold junction compensation (CJC) |
| mV: ± (50 µV + 0.1 % of span) |
| potentiometer: ± (0.05 % of full scale + 0.1 % of span, (excludes faults due to lead resistance)) |
| | Influence of ambient temperature | Pt100: ± (0.0015 % of measurement value in K + 0.006 % of span)/K ΔTamb*) |
| thermocouple: ± (0.02 K + 0.005 % of measurement value in °C + 0.006 % of span)/K ΔTamb*)), influence of cold junction compensation (CJC) included |
| mV: ± (0.01 % of measurement value + 0.006 % of span)/K ΔTamb*) |
| potentiometer: ± 0.006 % of span/K ΔTamb*) |
| *) ΔTamb = ambient temperature change referenced to 23 °C (296 K) |
| | Influence of supply voltage | < 0.01 % of span |
| | Influence of load | ≤ 0.001 % of output value per 100 Ω |
| Reaction time | worst case value (sensor breakage and/or sensor short circuit detection enabled) |
| mV: 1 s, thermocouples with CJC: 1.1 s, thermocouples with fixed reference temperature: 1.1 s, 3- or 4-wire RTD: 920 ms, 2-wire RTD: 800 ms, Potentiometer: 2.05 s |
| Galvanic isolation |
| Input/Other circuits | basic insulation according to IEC 61010-1, rated insulation voltage 300 Veff |
| Output/supply, programming input | functional insulation, rated insulation voltage 50 V AC |
| There is no electrical isolation between the programming input and the supply. |
| The programming cable provides galvanic isolation so that ground loops are avoided. |
| Indicators/settings |
| Display elements | LEDs |
| Configuration | via PACTware |
| Labeling | space for labeling at the front |
| Directive conformity |
| Electromagnetic compatibility | |
| | Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) |
| Conformity |
| Electromagnetic compatibility | NE 21:2006 |
| Degree of protection | IEC 60529:2001 |
| Ambient conditions |
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) |
| Mechanical specifications |
| Degree of protection | IP20 |
| Connection | screw terminals |
| Mass | approx. 130 g |
| Dimensions | 20 x 119 x 115 mm (0.8 x 4.7 x 4.5 inch) (W x H x D) , housing type B2 |
| | Height | 119 mm |
| | Width | 20 mm |
| | Depth | 115 mm |
| Mounting | on 35 mm DIN mounting rail acc. to EN 60715:2001 |
| General information |
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
